Starter Shingles: What They Do and How Many You Need

Quick answer: starter shingles are the first course installed along the eaves (and usually the rakes), underneath the first row of regular shingles. They put a strip of sealant right at the roof edge so the first course seals down against wind, and they fill the gaps under the first course's cutouts. Most starter bundles cover 100 to 120 linear feet, for example 105 ft for Owens Corning Starter Strip Plus and 120 ft for GAF Pro-Start. Order by the total length of your eaves and rakes.

For DIYers ordering materials and homeowners checking a roofing quote. Starter is sold separately from field shingles, so it's easy to forget.

What starter shingles do

A regular shingle seals to the one below it with an adhesive strip. The first course at the eave has nothing below it to seal to, and its cutouts (the slots between tabs or the gaps in an architectural shingle) would sit right over bare underlayment. A starter course fixes both problems:

Starters along the rakes aren't always required, but they're widely recommended, and some manufacturers' enhanced wind warranties depend on using their starter. GAF's no-maximum-wind-speed coverage, for example, requires qualifying GAF accessories, including its starter strip.

Starter shingle calculator

Enter your eave and rake lengths. Don't have them? The roof square footage calculator works them out for gable and hip roofs.

Starter length neededwith extra for cuts0
Starter bundles0

The default 80 ft of eaves and 68 ft of rakes is a 38 × 28 ft gable house at 6/12 with 1 ft overhangs, the same example used across this site.

Starter products compared

ProductCoverage per bundlePiecesNotes
GAF Pro-Start120.33 linear ft19 sheets that split into 38 piecesPieces are 6.5 × 38 in after splitting
GAF WeatherBlocker100 linear ft split, 50 ft as full sheets15 full sheets or 30 half sheetsPerforated so you can use full or half sheets
Owens Corning Starter Strip Plus105 linear ft16 shingles, 32 piecesOlder sheets listed 100 ft, so check the date on yours
CertainTeed SwiftStart116 linear ft18 pieces62 lb per bundle per CertainTeed's data sheet

Match the starter to your shingle brand if you want the manufacturer's full system warranty. Coverage can change between product versions, so the wrapper is the final word.

How to install starter shingles

These steps follow GAF's published Pro-Start instructions. Other brands are similar, but always follow the instructions on the bundle you buy.

  1. Drip edge and underlayment first. Starter goes on top of the eave drip edge and underlayment (and ice and water shield where used).
  2. Set the overhang. GAF says starter strips should overhang the eaves and rakes by ¼ to ¾ in. Where the drip edge sticks out from the roof edge, Pro-Start can sit flush with the drip edge.
  3. Sealant toward the edge. Lay the strip so its factory sealant is near the eave, where it will bond the first course.
  4. Offset the joints. Make sure joints in the starter don't line up with joints or cutouts in the first course.
  5. Rakes after eaves. Run rake starters up the gable edges, overlapping the eave starter by at least 3 in.
  6. First course on top. Field shingles should overhang at least as far as the starter. GAF's drip edge bulletin calls for shingles to extend at least ⅜ in and no more than ¾ in past the drip edge.

Can you cut regular shingles for starter?

With 3-tab shingles, yes, as long as the shingle manufacturer's instructions allow it. Simply flipping a full shingle upside down puts its sealant strip too high to do much good. Fine Homebuilding's method is to trim off the bottom 5 in, so the tabs are gone and the sealant sits near the eave.

For architectural shingles, manufacturers make purpose-built starter strips, and their system warranties are written around them. Buy the matching starter rather than improvising. With 3-tabs getting harder to find, a bundle of starter is usually simpler than cutting your own.

Add starter to the rest of your order

The shingle calculator totals bundles, starter, ridge cap, underlayment and drip edge together, with your own prices.

Open the shingle calculator →

Sources: GAF Pro-Start product data and installation instructions; GAF WeatherBlocker sell sheet and product page; GAF technical bulletin R-141 (drip edges and shingles); Owens Corning Starter Strip Plus data sheet; CertainTeed SwiftStart product page and data sheet; Fine Homebuilding, "The Starter Course".

Related guides

Shingle calculator

Bundles, squares, starter and ridge cap.

Calculate →

Ice and water shield

Where it goes along the eaves, and how many rolls.

Read the guide →

Architectural vs 3-tab

Warranty, wind coverage and cost compared.

Compare →