How this shingle calculator works
The calculator does what a roofer does on the back of an estimate sheet, in four steps:
- Area of each section. Length × width, measured flat, gives the footprint of that roof face.
- Pitch correction. A sloped roof has more surface than its footprint. We multiply by the pitch factor, √(1 + (rise ÷ 12)²). A 6/12 roof has 11.8% more surface than its footprint. See the full roof pitch chart and multipliers.
- Squares and waste. Divide by 100 to get squares, then add waste for cuts at rakes, valleys and hips.
- Round up to whole bundles. Squares × bundles per square, rounded up. You can't buy part of a bundle.
Worked example: a 40 × 30 ft gable roof at 6/12
This is the example loaded in the calculator above. The house is 40 ft long and the two roof faces each run 15 ft horizontally from eave to ridge, overhangs included.
| Step | Math | Result |
|---|---|---|
| Footprint | 2 × (40 × 15) | 1,200 sq ft |
| Pitch correction (6/12) | 1,200 × 1.118 | 1,342 sq ft |
| Squares | 1,342 ÷ 100 | 13.42 |
| Add 10% waste | 13.42 × 1.10 | 14.76 |
| Bundles (3 per square) | 14.76 × 3 = 44.3, round up | 45 bundles |
Skip the pitch correction and you'd order about 40 bundles, five short. That's the most common mistake we see in DIY estimates.
Choosing the right waste factor
Waste is the shingle you cut off and throw away. It's driven by how many edges and angles your roof has, not by its size.
- About 10%: plain gable roofs with two faces and few penetrations.
- About 15%: hip roofs, or gables with a couple of valleys. Every hip and valley means angled cuts on both sides.
- About 20%: cut-up roofs with dormers, turrets, several valleys, or short runs.
These are rules of thumb, not fixed standards, and they line up with published guidance. Owens Corning's DIY roofing guide says to add 10% to 15% to material totals for waste, more on complex roofs with more cuts. The JLC Field Guide to asphalt shingles starts from 10% and adds extra for hips, valleys, ridges and starter courses. If you track your own jobs, your real waste numbers beat any rule of thumb.
Many suppliers will take back unopened bundles. It's usually cheaper to return one extra bundle than to make a second delivery run for one missing bundle. Ask your supplier about their return policy before you order.
What the calculator doesn't include
These items depend on local code and roof details, so estimate them separately or ask your roofer:
- Ice and water shield at eaves and valleys. Many cold-climate codes require it. Use our ice and water shield calculator to estimate rolls.
- Step and wall flashing at chimneys, skylights and sidewalls.
- Roof vents and ridge vent.
- Nails. Count and length depend on the shingle and on high-wind requirements. Follow the nailing pattern on the wrapper.
Common questions
How many bundles of shingles cover 1,000 sq ft?
1,000 sq ft is 10 squares. At 3 bundles per square that's 30 bundles, or 33 with 10% waste. Make sure the 1,000 sq ft is roof surface, not house footprint. If it's footprint, apply the pitch multiplier first.
Do I use the house's square footage?
No. Living area ignores overhangs, garages, porches and slope. Measure the roof itself, or measure the footprint including overhangs and correct for pitch. Our roof measuring guide shows how to do it from the ground.
Are architectural shingles 3 or 4 bundles per square?
Most standard architectural (laminated) shingles are 3 bundles per square, but some heavier lines are 4 or more. The wrapper is the final word. Read more about bundles per square, or compare architectural vs 3-tab shingles.
Next step: get your measurements right
The calculator is only as good as the numbers you give it. Spend ten minutes with our step-by-step guide and order with confidence.
How to measure your roof →Related guides
Roof square footage calculator
Measure from the ground or from the attic, without climbing on the roof.
Read the guide →